Home > Cannot Ping > Cannot Ping Across Site To Site Vpn Sonicwall

Cannot Ping Across Site To Site Vpn Sonicwall

Contents

You need to enable "Management via this SA" in the VPN properties. Robert Reply Dave V. Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? Mike thebeagle says: September 17, 2015 at 1:18 am Laptop getting DNS correctly? http://sauvblog.com/cannot-ping/cannot-ping-router-but-can-ping-other-computers.html

Do you think you could help with this? I need to set up a 2nd site-site IPsec to a fortigate device in another middle east office. Your overall speed on the VPN will be limited to upload speed of the slowest connection on the VPN. In this case there is a data LAN and a VoIP LAN. https://community.spiceworks.com/topic/411887-sonicwall-vpn-site-to-site-cannot-ping-access-main-office

Sonicwall Site To Site Vpn Connected But No Traffic

This will be the NAME you use in following steps. Since I'm not familiar with SonicWall and I'm familiar with FortiGate, I run a debug on the FortiGate and I do see the pings coming in but I can't tell why I just configured two TZ 205's quickly and easily thanks to you! Then when you create the tunnel config they can find each other and not have any other firewall "in the way" and in between them.

asked 5 years ago viewed 4374 times active 3 years ago Related 1Route additional network through Sonicwall site-to-site VPN4How to configure remote access to multiple subnets behind a SonicWALL NSA 24000Routing Glad to be of assistance. I followed the instructions on this page https://support.software.dell.com/kb/sw7902. Sonicwall Vpn Tunnel Up But No Traffic I checked the gateway on the laptop and it is pointing to the remote Sonicwall.

Robert Mike says: September 22, 2015 at 12:20 am Robert, No worries on "being tardy." I appreciate your help. This is very much the case if the remote firewalls are on DHCP connections without a static IP but it is a rule I follow no matter what. CONTINUE READING Join & Write a Comment Already a member? https://community.spiceworks.com/topic/993730-sonicwall-site-to-site-vpn-only-one-direction-can-ping-or-connect-not-both-why Since the introduction of SonicOS Enhanced 4.0, a new option "Allow VPN path to take precedence " has been introduced.

If not then there is more digging required. Sonicwall Global Vpn Client Cannot Ping Lan If this is enabled, SonicWALL would drop traffic from any host communicating to another host over the VPN if Mcafee Client AV is not installed in it. I tried getting this going on my own, and have had some success. What you want is for both subnets to route through the VPN.

Sonicwall Global Vpn Client Connected But Cannot Ping

Note: Workstations have manual DNS settings, primary DNS is the their local Sonicwall router and Secondary is the Head Office DNS/DC Server ( so they can ping us at Head office https://support.software.dell.com/kb/sw7565 I was able to figure out what you meant about having multiple subnet's and configured both my routers. Sonicwall Site To Site Vpn Connected But No Traffic Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? Sonicwall Vpn Can Only Ping Gateway I just don't understand why.

About Advertising Privacy Terms Help Sitemap × Join millions of IT pros like you Log in to Spiceworks Reset community password Agree to Terms of Service Connect with Or Sign up http://sauvblog.com/cannot-ping/cannot-ping-nlb-vip.html The next day I had the same problem so I asked a co-worker to try with his Samsung and he was having the same problem through the SonicPoint. Glad my scribbles helped you out. Reply thebeagle says: October 16, 2015 at 10:36 pm Aaron -- I'll private message you on this. Sonicwall Site To Site Vpn Routing

up vote 0 down vote In addition to the "Enable Ping from LAN to Management Interface" already answered... Is the gateway setting on both your lan's correct, point either to the Sonicwall or a switch? Reply thebeagle says: November 21, 2014 at 3:26 pm Mike: Sounds to me like you need a return route to match the route you have on Main hub A to Site Check This Out Thanks for taking the time to share with the rest of the world.

Glad I was able to help you out. Sonicwall Icmp You might have the Sonicwall itself pulling DNS properly (for its own settings) but have something different in the DHCP scope settings. Many Thanks Reply thebeagle says: January 22, 2015 at 4:29 pm Hi, Mark: I have hit the same issue in the past (or at least similar).

I did have one question on the setup though.

Make note of what you enter as you will need to enter the same key on the other Sonciwall. Also, verify settings on your devices on the target subnets and ensure your gateway settings are correct. Why is this? Ikev2 Responder: Peer's Local Network Does Not Match Vpn Policy's Destination Network The Zone or Type of the Local or Destination Network is incorrectly configured Make sure the Address Objects are setup correctly.

If this is a critical issue you might want to just go ahead and place a support call. Static IPs at HQ on 192.168.1.* and statics at the branch on 192.168.5.*. That data line I'm testing on is actually for supplying wi-fi to our employees and any guests who might need it. this contact form These two items in place should force all traffic from the remote site to route over the VPN tunnel and out to the Internet via the central site GATEWAY IP.

I'm not Sonicwall tech support but I am happy to try and point you in the right direction if you can paint a better picture of how you are set up. If selecting more than one subnet add them to an Address Group. First Name Please enter a first name Last Name Please enter a last name Email We will never share this with anyone. Subnet B is handed out when a user uses the VPN Client back into our main office here where Subnet A is.

By default, Static Routes on a SonicWALL will overrule VPN Tunnel routes. To enable the remote traffic to get to azure we just had to add the azure network as a remote destination on the vpn setup. It will work for you as this is the recommended way to set up when one end is dynamic. Thanks very much…again!

Robert Reply Dan says: August 22, 2015 at 2:48 am I am new to SonicWall, and I followed this procedure exactly on both devices. Robert Reply Derek says: October 21, 2015 at 4:36 pm Hi Robert, Any updates on how to force all traffic from the remote site across the VPN. To use this process you have to decide on one Sonicwall as the “master” as it will always “listen” for VPN connections; the other Sonicwall will be the initiator. In other words, the ASA also needs to know that it needs to route traffic back to the Sonicwall local LAN via the tunnel.

Robert Reply Sean Upchurch says: April 9, 2015 at 5:30 pm Robert, Thanks for the help. What is the temperature of the brakes after a typical landing? Note all VPN destination networks defined in the Network tab of the VPN policies. Finally, have you restarted the remote sides modem and then the firewall?

Reply Cam Blair says: July 30, 2014 at 6:23 pm Awesome write-up. What you are doing with these two settings is defining the routing that will be baked into the VPN policy.